Report proyect

In our proyect the advances is are significant because the desing is ready, being  of wood but only the assembly is not finished because the material is not enough, the material mention is wood , our team now purchase more wod for complete the areas who need cover  and based in the electronic no have problems only need a taste and some materials who put inside the mechanism like LEDS, motors, encoder, sensors only need incorporade this things in the mechanism, in the part of programming is slow because in my team the nivel in programming is slow and the taste in this area is required for the motion of mechanism, in conclusion the mechanis is 50 porcent assembly the part of desing is almost finished only need material a cover , in the part or electronic needs taste and incorporate all electronic inside the mechanism , now in the part or programming is the word slow but all team make a big effort for finished in your completely the mechanis works toght for finish 

fuel gauge: the function or this object is take a measurement of fuel normally this piece can be found under the flywheel

engine: this motor have te more principal function, is move the car and take off-on this piece can be found in the front part or car

drive shafts;  is a mechanical component for transmitting torque and rotation, usually used to connect other components of a drive train that cannot be connected directly because of distance or the need to allow for relative movement between them.

pipeline: a conduit made from pipes connected end-to-end for long-distance fluid or gas transport this part can be found under the engine

exhaust pipe:  is usually piping used to guide reaction exhaust gases away from a controlled combustion inside an engine or stove. this part is under all car

silencer:   is a device for reducing the amount of noise emitted by the exhaust of an internal combustion engine. this part can be in the part back or car

brake: A brake is a mechanical device which inhibits motion, slowing or stopping a moving object or preventing its motion the brake can be in the wheels 

fuel tank: this part  have the fuel or car and cxan be found inside of car in the part of back

 tools of my survivol and multi tool

my multi have a blade, a ruler, a little pen for writhe in emergencys , also has a openers

 for bottles . and the cover is of my favorite color blue, but my survivol tool ha more things like

a hammer, a has a pick, it has a two blades one with saw for cut piece of glass, it has a pliers . a little lintern and it has a spoon and fork but i do not like but is no blue is yellow ,but so is very implement.

                                                       budget of the integrator proyect              

                  # tools and materials             tools and materilas                        price

                          2.5 meters                     stick of aluminum                      $40

                            6                                    screws with nut                        $18

                           12                                        rondanas                             $12

                           12                                           nuts                                  $6

                            1                                     protoboard                              $40

                            2                                 meters cable UTP                       $18

                            5                                            leds                                  $15

                           15                                       resistors                               $15

                            1                                     port parallel                            $89

                            2 meters                            of solder                               $12

                            1                                          cautin                                 $45

                            1                                            tape                                  $20

                            3                                             cd                                    $24

                            1                                          sticker                                $130

                            1                              integrade circuit LM55                  $10

                            1                                     fototransitor                            $10

                            1                                       fotodiodo                              $8

                            1                                     triplay (table)                          $8

                            3                                       capacitor                               $21

                            1                                          horn                                    $9

                            9                                        botoms                                  $45

                           20                                        screws                                  $10

Skateboard set up

Materials

one deck

two truck with axle each one

two plate

four wheels

ten nuts two more big

ten washers

spanner

eight  bolts

1) in the table place the truck with bolt, washers and with the nuts

2)   loosen with the spanner all the truck with all pieces or the step 1

3)  netx place the wheels in the axle of the truck

4)   place 2 nuts and washers and loosen again with the spanner

5)  And ready the skateboard are assembled

Part	Picture	Description
axle		It´s the part where incrusted the wheels
deck		It´s the base of al the table of skateboard
nose		The nose it´s the part front of the table
Plate		It´s the base of all parts of the table what allows have the wheels, axle, plate
Tail		It´s the part of back of the table
truck		It´s the part where incrusted all parts what allow move the skateboard
wheel		It´s the part for move the table

Integrated Project “Write Up”
Team number		team 2#
Group Members		Andrés Ramírez rubio Leonardo Sebastián villa González Luis Fernando delgadillo Mendoza Juan Manuel osto
My responsibilities
My responsibilities in the team are find information about the machanics and wirte, write, write about the information recopilate in the presentations for the teachers but is not only all write, is find, search information and work
Scope
My scope for the proyect is the creation the machanics for my calification and development in my career all this things I think for mi and my team
Communication strategies
My communications strategies are used the technologies for the proyect with the computers other is the electronic why electronic. Because the electronic is fundamental for the creation or proyect

Tools	description
	Gives the signal of “yes or no” when giving an order, command or to measure
	Works for assemble and disassembly of the object/machine by unscrewing bolts and nuts
	Itcover, holdinworks for multiple uses like covering , holding and wraping.
	They work for sustaining parts along with bolts and screw in the machine/mechanisms and can be either of metals or plastic.
	Its function is to transfer electric energy from any source to mechanism depending on the power it use as long as the transfer capacity is no bigger than the mechanism it is feeding
	It is an electric device that makes a series of electric pulses for movement.

advantages and disadvantages ofr have a blogg


advantages
1) is a tool for public information with friends about videogames, music, sports, T.V ETC.
2) is a social networt when others usuaries find information and discuss about themes of interest


 disadvantages
1) robbery information or hacking your account
2)censored for exposed themes inapropied for not all public and closet your blogg

http://ventajasdelb1og.blogspot.mx/
http://blogredapunad.blogspot.mx/p/ventajas-y-desventajas-del-USO-de-blogs.html
http://biblio-edu.wikispaces.com/Ventajas+y+Desventajas+de+un+blog+educativo

the arroba in spanish or at in english es the more important sign in the web address

the punto or point is important for al text an is used in web address

the underscore is important for all direccions in the web

 

the forward slash is important in all direccions electronics

the backslash is not diferent to forwardslash is very important for te world web

links

http://www.estacioninglesa.es/blog/guias-ingles/como-se-dice-arroba-en-ingles/

HELLO WORLD

HI GUYS MI NAME IS ANDRES I STUDIE IN THE FIE IN THE DEGREE OF ELECTRONICS AND COMMUNICATIONS ENGINEERING I LIKE THE FOOTBALL MY FAVORITES TEAMS ARE AMERICA OF MEXICO AND LIVERPOOL OR INGLAND AND I READ COMIC'S LIKE BATMAN,WATCHMEN,SUPERMAN,SPIDER MAN, ETC 

MY MUSIC FAVORITE IS THE DEATH METAL AND HEAVY,BLACK,TRASH BUT MY FAVORITE BAND IS SLAYER AND I LIKE VIDEO GAMES LIKE BATTLEFIELD 3 AND 4 I LIKE THIS GAMES VERY MUCH 

THIS IS ALL FOR NOW I HOPE HAVE A GOD REQUEST IN FIE BYE